설치편하고 감기좋은 데이토나 스로틀입니다 너무좋아서 2개나 구입했습니다감기편하고 즉각적으로 반응해서 너무나좋았습니다단점이 거의 없다고 생각합니다 의심없이 사용하시면 될거같습니다 가격대비 너무좋은 제품이라 생각합니다
View Detail
- Verkauf
- Instock
25.28 EUR (4,360 JPY) 27.83 EUR Save 9%
Webike Point: +44 pt
(0.25 EUR)
Lieferinformationen
In Stock, Ships within 24 hours.
Estimated arrival date around
Produktbeschreibung unten wird automatisch übersetzen durch Google.
Product detail
(PE, PWK, VM, PC, CR-mini, VM, Yoshimura YD24/28)
[Größe]
äußere Länge : 760mm
Aufrollen R : 29mm
[Spezifikationen]
Es ist möglich, bis zur MID Daytona Ride Bar bei 760 mm (29240) zu fahren.
Typ der Eindringung am Griffende
**APE muss auf Scheibenbremsen umgerüstet werden.
*Der Bremshebelhalter ist für die APE erforderlich.
≪When verwendet mit einem 2-Takt-Mischvergaser
*Nach dem Einbau dieses Produkts müssen folgende Arbeitsschritte durchgeführt werden: Öl aus der Ölpumpe entfernen und den Öleinlass des Vergasers abdichten.
*Wenn Sie diesen Bausatz mit TZR50/R oder TZM50R verwenden, müssen Sie auf einen großen Vergaser wechseln, da der normale Vergaser nicht lang genug ist.
.
Klicken Sie hier für die Bedienungsanleitung.
Klicken Sie hier für Reparaturteile
.
Φ20-Φ28 große Kabinen, die für optimale Wicklungen ausgelegt sind!
Super-Hochdrosselklappen-Kit für den optimalen Rückzugsbetrag für große Kabinen (PE, PWK, VM, PC, CR-mini, VM, Yoshimura YD24/28) von Φ20-Φ28..
(Bei einem Vergaser mit 28 mm Durchmesser kann er mit etwa 55 Grad Drehung auf Vollgas geöffnet werden..
Zur Verwendung mit dem NSR50 und NS-1, kann entweder mit den serienmäßigen Vergasern oder den Daytona Big Carb-Kits verwendet werden..
Vorsicht
* If there may be an instruction manual included, it will be written in Japanese.
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
New arrivals in used
New arrivals in used
Kundenbewertungen
Reviews with image
![[Webike Monitor] It followed on DISC-izing the <br>APE, and since the pure Throttle housing needed to be removed, it purchased.
The <br>carburetor is using Yoshimura TM-MJNphi24 CARBURETOR.
The <br>price became a conclusive factor which cheap one chooses](https://global-fs.webike-cdn.net/photo/article/23/1342268382223M.jpg)
![It is cheap anyway! Although other high throttle kits are the prices to which Yukichi flies from door to door, this product is a value price fairly. <br>Bad, whatever it may also say a result of a product to a thing, no one but [ high throttle ] and its th](https://global-fs.webike-cdn.net/photo/article/37/1276258465037M.jpg)
![Although it was with the object for the monkeys, it was used for APE. <br>When and it remained as it is, it was in the state where a throttle does not return -- [ be / the purchased lot / a blank ] [ a part of color ] [ the crack ] <br>Since there was no t](https://global-fs.webike-cdn.net/photo/article/28/1218372713428M.jpg)
Installed on: HONDA APE100 TYPE D
Dec 21, 2021
I bought this High Throttle for my Honda RS150 that fits perfectly. The quality of the item and the finish is great. I have to modify the item as i instaled it in a throttle body rather than the carb recommended but it still fit fine. This is cheap throttle an alternative throttle for a premium throttle. The item is package nicely. It was ship wraped in bubblewrap so item is protected. Make sure that the length of the cable is compatible witj the motorbike your going to use.
View Detail
Helpful?
Apr 25, 2021
High Solo with the best cost performance
Not suitable for street youth.
For Circuit.
Reason:Because it is difficult to adjust Speed with Throttle alone.
Helpful?
Jan 4, 2021
I thought that it was good for the repair measure of the accelerator wire off of my friend's SUPER CUB C50 modified 124ccPipe HandlebarSpec. and introduced it.
The carburetor and accelerator wire of a certain Horizontal TypeEngine 124cc Full kit became bad, and the carburetor was changed to YD28.
The taking out position was changed, and it became better temporarily, and it was relieved.
However, when I heard that Axel didn't return after switching back, and I visited to check, I found that there was a dislocation of the Accelerator Wire attachment part of the Switch box original.
I have repaired and adjusted the handlebar many times, but the angle of the handlebar cut, the length of the wire, and the position of the fitment were not good, so I gave up and considered a new installation.
I picked up a few kits that are hard to remove, easy to adjust, have long guide wire, high solo, and repair parts available, and have standard long wire that corresponds to the length of CUB frame.
At any rate, I'll replace the Grip at his request, and until he has more time. "Take the Small stuff home and work out the tentative matches and Ideas. So, I worked on it.
This is a perfect feeling. I'm looking forward to installing everything into the car and driving it in the real world.
Helpful?
Jun 11, 2017
It was the same product until now but Wire was somewhat elongated so I purchased it as a spare.
Since 2 St Parts are decreasing, I think that I want to use it for Large.
Helpful?
New Custom Articles
