Fork was pushed out to the limit, Rear was shortened to the limit at the ride height adjustment section, and even with -20mmSeat of db’s, it was quite Limit for 149cm to ride, but LINK was also Quantity at the lowest state.:Set and it gave me a little more room, so if you're worried about footing, I'd recommend it!
However, if you lower it that far, the Side Stand will be too long and the Motorcycle will stand upright, so the recommendation is to use a STANDCut or ZETA aluminum side stand with a -15mm tip!
- Instock
117.76 EUR (20,337 JPY) 134.34 EUR Save 12%
Webike Point: +203 pt
(1.17 EUR)
Lieferinformationen
In Stock (Lager des Partners), Ships around 24th Jul. 2025
Estimated arrival date around
Produktbeschreibung unten wird automatisch übersetzen durch Google.
Product detail
Halsband : blau (farbig)
Material : Aluminiumlegierung der Serie 7000
Anpassung : Niedrig-unten (weich) 5 Ebenen, Standard, Hochauftrieb (hart) 1 Ebene, insgesamt 7 Ebenen
**Die Staubdichtung ist nicht enthalten. Bitte verwenden Sie den Originalartikel oder bereiten Sie ihn separat vor.
*Sie können den Originalständer verwenden.
*Die Federung wird aufgrund der Änderung des Gestängeverhältnisses weicher sein..
* Das Bild ist nur als Referenz. Das gezeigte Bild kann vom tatsächlichen Produkt abweichen.
Die Sitzhöhe kann durch Veränderung des Abstands zwischen den Verbindungsstangen durch Drehen der Befestigungsposition eingestellt werden..
Das Gestängehebelverhältnis kann geändert werden, so dass die Hinterradaufhängung an die Streckenverhältnisse angepasst werden kann..
Sieben Ebenen des Absenkens (weich), Standard und eine Ebene des Hochhebens (hart).
Die Lager und Staubdichtungen sind vorinstalliert, es handelt sich also um eine Anschraubkonstruktion, die die serienmäßige Verbindungsstange ersetzt..
Das Material wird aus einer Aluminiumlegierung der Serie 7000 hergestellt, mit hoher Präzision bearbeitet und anschließend farbig eloxiert..
Vorsicht
* If there may be an instruction manual included, it will be written in Japanese.
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
New arrivals in used
New arrivals in used
Kundenbewertungen
Reviews with image
Fits:YAMAHA WR250R 07-17, YAMAHA WR250X 07-17, YAMAHA WR250R 07-17
Mar 30, 2022
Helpful?
Fits:YAMAHA WR250R 07-17, YAMAHA WR250X 07-17, YAMAHA WR250R 07-17
Mar 11, 2018
I bought it to improve the feet arrival of wr 250r.
In the past, I exchanged Spring back and forth, the car height at the time of riding fell down pretty, it did not splash softly, but still, I can not slip ass every time when stopping, sometimes it can run out of bad feet of getting on the descent I tried purchasing a product.
I thought it was good to make it as adjustment type because it gets softer than I thought would actually be installed.
When this is installed, the Side Stand is too long, either shortening or needing to replace the Side Stand for X.
Helpful?
Fits:HONDA CRF450R 17-20, HONDA CRF250R 18-21, HONDA CRF450RX 17-20, HONDA CRF250RX 19-21, HONDA CRF450L 19-20
Jun 30, 2019
It was exactly what I expected
The design is good and the product is as expected? (^-^) /?
I recommend it to everyone
I bought it to improve its footprint, and I'm sure it will achieve its purpose and give you peace of mind from now on You can drive
Helpful?
Fits:HONDA CRF450R 17-20, HONDA CRF250R 18-21, HONDA CRF450RX 17-20, HONDA CRF250RX 19-21, HONDA CRF450L 19-20
Jun 9, 2019
I bought them to improve my footing and I'm happy with the Potential as I expected
Before, he was seated in Seat with his feet in a very splayed out position, but his feet are just his toes
It's on the ground, so you can enjoy driving in peace? (^-^) /?
Helpful?
Fits:HONDA CRF250RALLY LD 17-20, HONDA CRF250L LD 17-20, HONDA CRF250L 13-20
Sep 30, 2018
If fine adjustment within 25 mm is necessary
I installed it on the CRF 250 M of MD 44, but Adjuster should be fixed with Tape etc. at the time of installation. When I tightened with Torque44Nm prescribed without noticing that I misaligned at the time of tightening, how swollens are !! (It is as shown in the picture) I broke the protrusions on the body side and broke the 20,000 LINK to par, but I could install it again. I thought using it, I wanted to lower the adjustment by 10 mm more, I was more rough and I did not need fine adjustment within 25 mm. If fine adjustment is unnecessary 5000 yen cheap Adjustment of Zeta None VERSION is good? But it is cool so it was good.
View DetailHelpful?
New Custom Articles
