Mechanischer Kupplungshalter L-29 [Nur Inhaber]

Since I changed the Brake Side to brembo, I diverted the Clutch holder L-29 from the previous car to the Ninja1000SX.

The Ninja1000 is light enough to handle in NORMAL mode, and there is absolutely no need to make it any lighter, but there is no need to make it any lighter than it is in QUANTITY:Pair (for Left and Right) I have a disease that I want to align with bremboLever. (Lol)

I've considered the GALE SPEED before this, and it was tempting to choose the best one for me because of the large number of Lever types, but I'll save that for next time.


Installation, the experience I had earlier when I replaced the Ninja1000SX's Brake with a brembo will come alive here. After all, the signal line of the state switch of Clutch is necessary for the On-Off control of AutoCruise Control as well as Brake Side.

First of all, remove the OEM Clutch holder, but you need to adjust the body of the car because the adjuster on the holder side does not extend the cable.

Hi. Here's a shocking revelation:you have to remove the SIDE & lower cowl to adjust it!

I was aware of this from the beginning, but I doubted that there was a motorcycle with such a bad disassembly and maintenance, but I couldn't do it even though I tried many times.

If you come to the point of removing the OEM Clutch holder in some way, you can also remove the Switch.

The OEM Switch is an integral part of Harness, so you have to cut it off at the appropriate point.
The appropriate position should be aligned with the temporary assembly of the holder to be replaced.

After disconnecting the Harness, I used the Model 110 Connector again this time. It is important to note that the signal line of the new Clutch switch is not reversed on-off.
If you make a mistake, it will be a terrible mistake.

If you can connect the Clutch switch to the Harness on the car body side, it's just a matter of assembling and adjusting the Cable.

Don't forget to install the attached Spacer at the cable end and assemble it to the Clutch holder.

After this, adjust the length of Clutch by Cable.
The reason for this is that the Cable will be stretched as you use it, so it's easy to deal with that by adjusting the Holder side.

It is important to note that the outlet position of CableLine is slightly different between Koken's Clutch holder and OEM.

When I adjusted it, I adjusted quite a lot, so I was anxious and impatient during the adjustment process, but I was able to install it safely after using a little bit of adjustment on the Holder side as well.

Operation power is also slightly lighter, and Lever's pull charges are much lower than the OEM's, so it can be operated more lightly.


If I put back the arrangement of Harness of LeftSwitch to the original, it is the end, but Harness was bundled to Clutch Cable. Because it is impossible to return it to the original position due to the influence of the change of Clutch CableLine, Harness arrangement is reviewed and changed.


I didn't expect to spend so much time on replacing the clutch holder, but after all the hard work, I am satisfied with the result.

bremboLever set (Out of print) Why is it cheaper to purchase separately with bremboLever than to purchase?
I am satisfied because the appearance will change.

The color of Standard Product was a little shabby so I tried it like NORMAL っ ぽ い Black.
It looks good, it became lighter than I thought.
However, there is too much play in Lever itself! It moves quite well up and down.
Besides that price, this accuracy is a structural problem.
Manufacturer here seems to be a lot of good products, but all I bought is Ha Gap.

ACCOSSATORacing clutch,
GALE SPEEDWire Clutch Holder Kit,
I was worried but brembo's MechanicalClutch Leva
As it is currently installed, the price 32000 yen (tax-excluded) of
We selected only Holder L-29.
We only port the Lever division.

Holder comes with Clutch switch.
Clutch switch has 2 Patterns.
Wire play adjustment & Lever position adjustable.

The Clutch switch can be a Small Type,
I feel a little tired..
Three lines are connected, but when installing,
Treating it somewhat seems to break from the root Pin.

Especially finger Quantity : People who are 2 pc or 3 pcs,
Feeling the Wire to be drawn,
If you do not set Lever to a long distance
Clutch may not run out.
Making a little play makes it lighter,
No problem if you cut Clutch with 5 fingers.

Look, brembo's Brake MASTER and
It is GOOD because I feel unity.
However, the color was not better than I thought.

The price is also high (With Lever, tax included 40,000 yen over) ,
It was slightly lighter than NORMAL,
There is no need to forcibly change.
As stated above, if you are concerned about the appearance it is Recommendation.
Do not forget to buy Seal of ItalyMark on bespoke.

Depending on the model, Clutch
Because it seems there are times when it can not be cut,
Type of Holder is L-24 or L29 or L34
Let's choose firmly from Lineup.