I installed it on the upper side of the NINJA400's rear master.
Rear brake piping can be long and complicated, especially on ABS-equipped models, which can make it difficult to bleed.
Therefore, I installed this Air Free Banjo Bolt in anticipation of improving air extraction around the Rear master.
It's easy to install:Remove brake fluid on the rear side, remove the rear master - upper Banjo bolt, then install this Air Free Banjo Bolt. (Crash washer is included in the kit.)
Then inject Brake fluid and remove air. I tried this Air-free Banjo here. The result is probably OK. it is uncertain whether it is the effect of this Air-freeBanjo, but Fluid injection and air removal could be completed in Smooth without air bite.
In the case of NINJA400, if you install the Air-free Banjo on the upper side of the rear master, it will interfere with the original plastic cover. Therefore, it is necessary to cut a part of the resin cover. I used a hot knife to cut the resin cover as shown in the photo.
- Instock
19.92 EUR (3,440 JPY) 22 EUR Save 9%
Lieferinformationen
In Stock, Ships within 24 hours.
Estimated arrival date around
Product detail
Hergestellt von GOODRIDGE
Material : Rostfreier Stahl
Schraubenteilung : P1.25 Einzeln
2 Brechscheiben enthalten
**Bitte überprüfen Sie vor der Auswahl die Schraubenteilung..
Klicken Sie hier für die Gummikappe für luftfreie Hohlschrauben
Klicken Sie hier für andere Typen..
Die Flüssigkeit kann zur schnellen Entlüftung aus dem entlüfteten Teil der Hohlschraube entfernt werden.. Sie können aus einer breiten Palette von Farben wählen.. (Einige Farben sind je nach Schraubenteilung nicht erhältlich.. )
Vorsicht
* If there may be an instruction manual included, it will be written in Japanese.
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
New arrivals in used
New arrivals in used
Kundenbewertungen
Reviews with image
Sep 26, 2020
Rear master - for venting air from the top
May 22, 2016
Material : Stainless Steel's Merit - Demerit
Air bleeding work became easy, but Material : For Stainless Steel it feels a bit easier to loosen. I think that it is better to tighten further after installing it for a while. Breed also.
It is good that Wrench is hard to lick, but on the contrary the fear of biting into Caliper.
Also, Rubber cap has been disconnected with 2 detachments.
I do not want to worry about Parts around Brake, so I'm inspecting it, but it's inconvenient in that sense.
Material : Aluminum may be less expensive and cheaper.
Jul 10, 2022
Used for Rear Sam Brake master
Rear master (Gail) It is easy to use because it is used for
Purchased this time with the addition of Sam Brake master.
Air removal is much easier.
Dec 13, 2021
Required for NisshinHorizontal TypeMASTER
I was having a hard time bleeding the air out of the NisshinHorizontal TypeMaster Cylinder. When I used this Banjo bolt, air bleeding was finished without difficulty. The hose for air bleeding sticks firmly and does not come off easily.
View DetailDec 30, 2020
Required for the old Crab caliper?
Installed on brembo old Crab caliper.
With the Caliper installed, the Bleeder Bolt is in a position where there is no way to turn it, so it's nice to have a product like this.
This allows you to replace the Fluid without removing the Caliper.
(You have to remove it to bleed air.)
The screw part is too long to fit on the OEM Banjo.
Two Washer on top and bottom (Total Quantity):(1 Set of 4pcs.) I used it.
New Custom Articles
