* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
I was using a PC20 but for further power up, I was using a VM22 However, the setting did not come out, and I think it is more than Mikuni I'm a KEIHIN guy, so I switched to this one This too, as well as well-written on the Net about Chinese carburetor T/A Japan It was an engraved object Just like an ordinary KEIHINcarburetor "KEIHIN It is also engraved Also "Made in China It's nice and graceful that Seal of the company is putting up lol
The construction is somewhat beautiful The appearance is not inferior to the original There is no problem around the float packing inside, but you should remove the Jet once and clean it is a good idea I was a little reluctant to remove it around the Jet and found a piece of SmallSana BALI The Jet itself also had some scratches at the bottom that looked like it had bottomed out, so even though it's the same count, KEIHIN OEM I feel more comfortable changing to the (The jets were common to the original PD22.)
By the way, I use it as RemoteChalk Since the NSF100 OEM Parts Cable can be used by pontooning it, the vehicle with Cowl If you can't access carburetor directly, you can use Recommendation It is
It is a shoddy product. It takes Engine with Pon. When I twist the Fuel Cock, the Cook comes off from the middle. I heard that there is no replacement parts.View Detail
It was very difficult to start the engine of SEROW225 in winter, I tried with various NORMAL negative pressure carburetor, but it was not improved. I found a lot of reviews that PWK is severe, so I decided to use PE Type. From this experience, I installed the same one to improve the sluggish feeling of gAXIS Second Type Model, after all, setting is very easy and it runs well. Did you think it was a good product?View Detail
I put FTR223Engine on my XLR125 and I can't put Normal cab on it, so I chose this carburetor and put it on it. mj120 It's around SJ35, but for some reason the Idling area is jerky.
I went to the trouble of getting six of Mikuni's Pilot Jets for TMR and went through a lot of trial and error, but no matter which Jet I put in, the Idling doesn't get high enough unless the screw return rotation is close to fully closed. And yet, when I look at the Plug, it is completely black.
In the end, I was able to compromise around 35, but inevitably, on Touring where I run at high GEAR and low Engine RPM, it runs very jerky. The XLR125ROEMcarburetor doesn't have enough acceleration, but it's perfect around Idling.
When I set the proper Pilot screw back, the Idling RPM apparently goes up and down. I don't think it's about the setting anymore.
Unfortunately, it's unclear which Mikuni made this or if it's completely fake, ha Gap or Maybe they're all like this. The acceleration is good though.View Detail
It's cheap, but the processing is not good at all. However, it is not so that the performance is not good, and I do not know well because it is after I fix it by myself, but I can use it normally. You might be better off buying a cheaper Chinese product from Large Hand Mail Order Site.View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING