* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
Purchase compared to OEM and other Other Brand Products. The Material is Stainless and rust resistant. The wall thickness is also thick, when I stepped over the tree, it became a balance, but it was surprisingly stable, it was large to pull it out. Cost is good and if you are hesitant about the price, try it. It doesn't look or look obvious, but it does the job well.
Worst installation accuracy Using the included Frame buffer material will make installation difficult. You will probably hear a buzzing sound in the future. Don't be fooled by the appearance, buy an OEM product. I'm buying a new one too. It was a colossal waste of money. It's nothing but trash.View Detail
I think it's good that the design is simple, and that it's thoroughly crafted down to the smallest detail (chamfering of the edges, etc.).
However, I think the included Spacer is poor and not long enough. If you install it with this Spacer, it will contact the Frame at 4 points (although it may be designed to have strength there). Isn't it possible that Frame Rust or noise is generated from the contact points?
In addition, it has Sponge to fill the gap, but I think this absorbs water and cause FrameRust. If you are going to use it like a TRIAL, I think you should guard it well with Rubber, not Sponge.
I don't have sponge. I don't have any sponge.View Detail
Since the US only inported the Super Sherpa for a few years there are very few aftermarket parts available here. This is a super heavy duty plate that will protect. Only compaint to be honest is i wish it had some side protection for the engine but it fits the bike well. With not too many options avaialble it's way better than the tin plate that was factory. I can now put it on a box stand for storage too. Arigato View Detail
This is a great skid plate. I would have given 5 stars if it hadn't needed some fitting and spacing to fit my bike. It needed 3/8" spacers at the rear and a thick 1/8"washer at the front. I would still very much recommend this plate. It is wide and flat and thick which is what we want. Shipping was pretty fast too considering this seems to be kind of a rare part and had seen it out of stock on other websites. View Detail
Made of strong sturdy alloy plate 6mm thick.Alot wider than standard 250mm wide,protects gear change shaft.Change engine oil without taking skid plate off.Cut out slots allow more cooling air around engine crank case.View Detail
There were no problems with the lower part of the Engine during touring on forest roads, as it provided sufficient protection from stepping stones and other obstacles. Thanks to the Flat shape, it was also Point that washing the car after driving was easy.View Detail
If you install it bare, it will hit the bottom bolt protrusion of the Crankcase. This means that when you hit the Guard I'm about to split the Crankcase. I put a Spacer in the back Screw to float it. It would be better if the SIDEGuard part was also added. It is very good to change the oil with the Guard on. Installation itself is not difficult. Unfortunately, the Shift Pedal will hit the pedal if you leave it as is. It should be Direct. At this thickness, if it is installed properly, it should be It is safe even if you hit your bottom against a rock on a slippery slope.View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING