?
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
I converted 525 set to 520 and increased the ratio for my offroad racing w650It weights 136 gramsthe stock ones is 195 grams
Fits: KAWASAKI ER-4n 11-13, KAWASAKI ER-6f 07-10, KAWASAKI ER-6f 09, KAWASAKI ER-6n 06-14, KAWASAKI ER-6n 09
After replacing the chain, large gear, and small gear at once with Sunstar products about 12,000km last year, I liked it so much that it was different from the genuine product, so I bought it to keep it in stock before I exchanged it.It is said that there is a little noise compared to the genuine, but I personally did not feel it, and the feeling of acceleration is faster than the genuine because of the lightness.View Detail
Fits: KAWASAKI ER-4n 11-13, KAWASAKI ER-6f 07-10, KAWASAKI ER-6f 09, KAWASAKI ER-6n 06-14, KAWASAKI ER-6n 09
Brand: SUNSTAR Commodity: SUNSTAR Front SprocketUse model: NINJA400 17Delivery time: The time limit quickly took 20 days to reach the Chinese customsUse experience: SUNSTAR Rear Sprocket Duralumin can increase flexibility and make the engine exert greater performance. I have used it for 1 year, and the fuel consumption and power have improved compared to before.View Detail
Fits: KAWASAKI ER-4n 11-13, KAWASAKI ER-6f 07-10, KAWASAKI ER-6f 09, KAWASAKI ER-6n 06-14, KAWASAKI ER-6n 09
It seems to be a standard YamahaRENAISSA. The engine braking is smoother, and the torque feeling is reduced, but it is a good part in the end.View Detail
Fits: KAWASAKI ER-4n 11-13, KAWASAKI ER-6f 07-10, KAWASAKI ER-6f 09, KAWASAKI ER-6n 06-14, KAWASAKI ER-6n 09
The W800 is capable of reaching approximately 2000 rpm in 5 mph (60 km/h), and has the same high-revving engine characteristics as the SS Compared to Motorcycle
It's a low rpm and tosses and turns...
This is when you get into the 100km/h range of speeds above 80km/h on the highway
It doesn't bother me as a thumping vibration of the Engine, but as an unpleasant Vibration
I put Weight in the Handlebar to absorb the slight vibration, but
Still, through footpegs and grips (Personally.) The unpleasant vibration continues
The SDR that used to be my favorite car (200) It's better than that, because that thing was a sharp vibration that made my feet itch
But uncomfortable
So I decided to change the GEAR ratio to deal with it
I can't find a 16T model that fits the W800's standard 15T
The same goes for the Rear Driven Sprocket, which is a 37T, so I'll be looking for a 35T or so I can't find the
I found both front and rear while trying to change the compatible car model from W800 to EN-6f
Let's try it! Since it's a project, I bought FrontSprocket this time with an emphasis on Cost
Since the Speed sensor is a W800 located in the front sprocket, the speed Meter value is out of whack
If you do the math, it's 6% more Well, I guess it's within acceptable limits
I have no complaints from bottom to top thanks to the slow Torque, which was rather fat when I tried it out
I'm going to ride this for a while
SUNSTAR's Sprocket has been a great help to me with the SRX-6, so I'm comfortable with it
View Detail
Fits: KAWASAKI ER-4n 11-13, KAWASAKI ER-6f 07-10, KAWASAKI ER-6f 09, KAWASAKI ER-6n 06-14, KAWASAKI ER-6n 09
SUNSTAR and Afam are famous for Sprocket, but I purchased the SUNSTAR product I used before..
good point
The point that the price is inexpensive
It uses S45C, Vickers hardness HB 160 is sufficient and it can be expected to have a long service life.
A bad point
Difficult to understand front and back (Perhaps it is better that the letters are written).
important point
I think that there are more people to exchange for Chain exchange, but if you turn off Chain, you will need Impact wrench to remove Center check nut. Let's remove DriveSprocket first.
In the case of Yamaha car Center check nut's Piece is 32 mm.
Let's use the new article to stop looseness of Center check nut.
Let's look at the condition of Oil seal of Drive shaft together.
As a reliable Manufacturer you can recommend it.View Detail
Fits: SUZUKI BANDIT250VZ 97-00, SUZUKI BANDIT250V 95-00, SUZUKI BANDIT250 95-00, SUZUKI DJEBEL250XC 96-08, SUZUKI DJEBEL250 92-95
My old sprocket has zero play, Sunstar has movement on the splines. Splines over time will be destroyed if installed. Bought OEM to avoid another bad purchase. Also bought a brand new main output shaft for future engine overhaul, same result (play on splines)View Detail
Fits: KAWASAKI D-TRACKER X 08-17, KAWASAKI ELIMINATOR SE 23-25, KAWASAKI ELIMINATOR 23-25, KAWASAKI KLX230R S 22-24, KAWASAKI KLX230R 20-24
Item received early den expected.getting ready for my next sporket and chain change.packing was always tip top.highly recommend to shop at webike.thank you TEAM WEBIKE.View Detail
Fits: YAMAHA MT-09 TRACER GT 14-19, YAMAHA MT-09 TRACER 14-19, YAMAHA MT-07 14-18, YAMAHA FZ8S 11-14, YAMAHA FAZER8 11-14
Delivery was prompt & no issues. Satisfied with their service.Do make sure the products fits your bike otherwise you could try ask them.View Detail
Fits: HONDA CBR250RR 23-24, HONDA CBR250RR 17-22
About quality and texture 10/10About the feeling of use 10/10Products to buy together 5/10Difficulty of installation 5/10Cost performance and comparison with other products 10/10About shipping and packaging 10/10View Detail
Fits: HONDA CBR250RR 23-24, HONDA CBR250RR 17-22
About quality and texture 10/10About the feeling of use 10/10Products to buy together 10/10Difficulty of installation 5/10Cost performance and comparison with other products 5/10About shipping and packaging 5/10Any concerns, cautions, or advice when purchasing...no cocern just goView Detail
Fits: KAWASAKI VULCAN800 Drifter 95-06 Configuration for 520 conversion, Others DYMAG 2011 and later production models I.D. 120mm, PCD140mm, mounting hole 6-10mm *Not available for spider type, YAMAHA XJR400S 93-08
I converted my W650 from 525 to 520 chaind and sprockets. The bike lost almost 1 kg after that.This sprocket weights 226 gr. The stock one is 670 gr.Also i increased the ratio for offroad racing purposes.View Detail
Fits: KAWASAKI W650
Excellent product.it includes everything for bore up to 811: liners, pistons, gaskets, rings and pins.Packed very well.Technical documentation is only in japanese =(I just only hope there will be information about thermal clearances for boringView Detail
I love the product and how the valve cover now matches with the carburetors.Installation was easy and there were no problems with itView Detail
Fits: KAWASAKI W400 , KAWASAKI W650
Made from nice and solid steel, pleasant to the touch.For my purposes and my lamp it turned out to be too short. The headlight was flush with the fork legs.If it were Z-shaped and 5 cm longer, it would be ideal.View Detail
Fits: KAWASAKI W650 , KAWASAKI W400
They are made from composite material and lighter than the stock onesThinner and more elegance, especially with sr400 gas tank.You need to remove air box and to relocate all electric parts from left side.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING