Luftschutz und Styling auf hohem Niveau mit einem Winkelverstellmechanismus.
Der Bildschirmwinkel kann durch Betätigung der oberen Brücke stufenlos an die Fahrbedingungen angepasst werden.
Der Hauptkörper des Bildschirms besteht aus 3 mm dickem Polycarbonat (Hartschicht-Spezifikation).
Erhältlich in den Farben klar und rauchfarben und in drei Größen.
8-mm-Bolzen auf beiden Seiten, leichter Durchmesser für normale φ180mm.
Erfordert einen geteilten oberen Griffhalter..
Wenn der obere Lenkerhalter integriert ist (bei geteiltem oberen Halter), wird der Klemmblock von Geira Shield in der Mitte des Lenkergriffs installiert..
Wenn die obere Lenkerhalterung (der Teil, der den Lenker an Ort und Stelle hält) in einer einzigen Einheit integriert ist, ersetzen Sie sie durch eine geteilte obere Lenkerhalterung, bevor Sie den Gaillashield installieren..
Gaillard-Schild
Windschutzscheibe mit variablem Winkel und kubischer Oberfläche für hervorragenden Luftschutz.
Gaila bedeutet "Kimono in Rüstung", und dies ist eine Frontverkleidung mit einem Design, das Robustheit und Eleganz vereint..
Eine FRP-Innenstrebe wird in den Schirm eingesetzt, um die Steifigkeit des Schirms zu erhöhen und gleichzeitig einen einzigartigen Frontbereich zu schaffen..
Darüber hinaus ermöglicht der einzigartige Winkeleinstellmechanismus von Sick Design eine stufenlose Einstellung des Bildschirmwinkels entsprechend den Fahrbedingungen von allgemeiner Fahrweise bis hin zu Hochgeschwindigkeitsfahrten..
Der Hauptkörper des Bildschirms besteht aus 3 mm dickem Polycarbonat (Hartschicht-Spezifikation).
Erhältlich in drei Größen, klar und rauchfarben.
Dies ist der höchste Grad an Windschutz unter den am Lenker montierten Verkleidungen, da es möglich ist, die Verkleidung auf den Fahrzeugtyp und den Körperbau des Fahrers einzustellen..
Anschraubkonstruktion für kompatible Automodelle
Anschraubtyp ist verfügbar..
Die Vorderseite des Bildschirms ist so gestaltet, dass sie das Licht abdeckt und eine scharfe Frontfläche erzeugt, ohne die Lichtmenge zu reduzieren..
Für die Installation sind keine speziellen Werkzeuge erforderlich..
Einfach anzubringen und abzunehmen mit bordeigenen Werkzeugen und kompatibel mit der Fahrzeuginspektion..
Bildschirm mit One-Touch-Winkel einstellbar
Rechte und linke Gummihalterungen auf beiden Seiten der Leuchte, und der Winkel des Bildschirms kann um diese beiden Punkte herum eingestellt werden..
Die seitlichen Befestigungsschrauben und die Befestigungsschrauben der inneren Strebe sind aus haltbarem rostfreiem Stahl hergestellt..
Der Winkel kann schnell und einfach ohne Werkzeug mit dem Einstellknopf in der Mitte des Lenkers eingestellt werden (Werkzeug für MT-01 erforderlich).
Die Reichweite der Bewegung hängt vom Fahrzeugmodell ab..
Der Winkel des NC700S kann in zwei Stufen eingestellt werden, während der Winkel des VMAX1700 mit dem linken und rechten Knopf eingestellt werden kann..
Der Bildschirm ist in drei Größen erhältlich: S, M und L
Die Größe L ist ideal für große Fahrräder und bietet erstklassigen Windschutz für schnelle Fahrten.
Die Größe M ist so konzipiert, dass sie gut mit einer Vielzahl von Fahrrädern funktioniert, ganz zu schweigen von den Naked Bikes der Mittelschicht..
Die Größe S ist ideal für die Viertelgröße, ohne auf Windschutz zu verzichten..
Die Form des Bildschirms ist in den Größen S, M und L gleich, und die Länge und Breite werden durch Abschneiden des hinteren Endes angepasst..
Die Montageposition des Bildschirms ist die gleiche und kann je nach Anwendung auf eine andere Größe geändert werden..
Die Bildschirmgrößen S, M und L sind alle gleich teuer..
Für die Bildschirminstallation werden haltbare Edelstahlschrauben, Polycarbonatscheiben und Sicherungsmuttern verwendet..
Im Falle eines integrierten oberen Lenkerhalters (geteilter oberer Halter)
Der Klemmblock des Gyroskopschilds wird in der Mitte des Stangengriffs installiert..
Wenn die obere Lenkerhalterung (das Teil, das den Lenker an seinem Platz hält) in den linken und rechten Lenker integriert ist, ersetzen Sie sie durch eine geteilte obere Lenkerhalterung (Originalteil/2 Teile des Herstellers) und installieren Sie dann den Gaillashield..
(Honda-Original-Teilenummer:53131-MS8-000 / Kawasaki-Original-Teilenummer:46012-1191)
Wenn Sie ein Geira-Schild haben, von dem nicht bekannt ist, dass es auf Ihr Fahrzeug zutrifft
Die Anpassung des Gyroskopschilds an jedes Fahrzeugmodell erfolgt durch Veränderung der inneren Strebe und der Beschläge..
Es gibt keinen wesentlichen Unterschied im Aussehen zwischen den Produkten für alle Fahrzeugtypen, jedoch kann der Einbau des Produkts in andere als die oben aufgeführten Fahrzeuge unerwartete Probleme verursachen, was sehr gefährlich ist..
Windshield with angle adjustment mechanism that combines air protection and styling at a high level.
Stepless adjustment of the windshield angle to suit the riding conditions by means of the controls on the top bridge.
The windshield itself is made of 3mm thick polycarbonate (hard coat specification).
The color is set up clear and smoke, and the size is also selectable from three kinds.
Bolt 8mm on both sides of light, light diameter is for stock Φ180.
A split handle riser is required.
■In case that the handlebar upper holder is an integrated type (Regarding split type upper holder), the clamp block of Guyra Shield is to be installed in the center of the bar handle.
If the handlebar upper holder (the part that fixes the handlebar) is integrated into the left and right, replace it with a split type handlebar upper holde and then install Guyra Shield.
■Guyra Shield
Variable angle type windshield with tertiary curved surface for superior air protection.
Guyra means a suit of armor, and this front fairing is designed with a fusion of ruggedness and elegance.
The inner bracket made of FRP is set inside the windshield to increase the rigidity of the windshield and at the same time to produce a unique frontal area.
In addition, the angle of the windshield is full adjustable according to the riding conditions from general riding to high-speed riding by the angle adjustment mechanism originally developed by Chic Design.
The windshield itself is made of 3mm thick polycarbonate (hard coat specification).
Available in three sizes and in clear and smoke colors.
The fairing can be set up according to the type of vehicle and the rider's physique, and boasts the highest level of windproof performance among handlebar mounted fairings.
■Bolt-on design for compatible models
There are different types for each model, and installation is bolt-on.
The front side of the windshield is designed to cover the light a little to produce a sharp front face without reducing the amount of light.
No special tools are required for installation.
It can be easily detached with only an in-vehicle tool.
One-touch angle adjustment windshield
The angle of the windshield is adjustable around the rubber mounts on both sides of the light.
The side mount bolts and the bolts to fix the inner bracket are made of stainless steel for durability.
The adjustment knob mounted in the center of the handlebar allows quick and easy angle adjustment without the use of tools (tools are required for MT-01).
The range of motion varies depending on the model.
For NC700S, the angle can be adjusted in 2-way (up and down), and for VMAX1700, the angle can be adjusted by the left and right knobs.
■Windshield sizes are available in S, M, and L
The L size is ideal for big bikes and provides the best wind protection for high-speed cruising.
M size is designed to be compatible with a wide range of bikes as well as middle class naked bikes.
The S size is the most compact size without sacrificing windproof effect and is suitable for quarter class size.
The shape of the windshield is the same for all sizes (S, M, L), and the length and width are adjusted by cutting the back end
The mounting position of the windshield is the same, so it can be changed to a different size windshield depending on the application.
The price is the same for windshield sizes S, M, and L.
Durable stainless steel screws, polycarbonate washers and lock nuts are used for windshield mounting.
■In case that the handlebar upper holder is an integrated type (Regarding split type upper holder),
The Guyra Shield clamp block is mounted in the center of the bar handle.
If the handlebar upper holder (the part that holds the handlebar) is integrated left and right, replace it with a split type handlebar upper holder (manufacturer's stock part / 2 pieces) and then install Guyra Shield.
(HONDA OEM Part No: 53131-ms8-000 / KAWASAKI OEM Part No: 46012-1191)
If you have a Guyra Shield for which you are not sure of the application on the type of vehicle
Application of Guyra Shield to each model is done by changing inner bracket and metal fittings.
There is no significant difference in appearance between the two types of vehicles, but it is very dangerous to install the product on other types of vehicles as it may cause unexpected problems.